전체상품목록 바로가기

본문 바로가기


| [구매대행 / 무료배송] 5.8Ghz 32CH 600mW RC832+TS832 영상송수신기 콤보

(해외배송 가능상품)
추천메일   |   
상품조르기   |   
기본 정보
상품명 [구매대행 / 무료배송] 5.8Ghz 32CH 600mW RC832+TS832 영상송수신기 콤보
제품가격 75,000원
제조사 / 원산지 XCOPTER / 중국
구매수량 수량증가수량감소
제품코드 98167

개인결제창을 통한 결제 시 네이버 마일리지 적립 및 사용이 가능합니다.

혜택
배송비
무료 ~ 3,000원 (5만원 이상 무료)  |  도서산간 배송비 추가
상품 옵션
옵션 선택
상품 목록
상품명 상품수 가격
[구매대행 / 무료배송] 5.8Ghz 32CH 600mW RC832+TS832 영상송수신기 콤보   수량증가 수량감소 75000
총 합계금액 (수량)
0 (0개)
SOLD OUT 관심상품등록 장바구니 담기 바로구매하기예약주문
THIS IS THE NEW 32-CHANNEL EDITION OF 5.8G 600mW A/V WIRELESS SYSTEM.

Features:

• 32 channels: Cover A, B, E bands and F band (Airwave band), 4 bands and all frequencies compactable; 
• Two switching buttons: CH button for frequencies channels switching, FR button for frequencies bands switching;
• Two digits display: one for CH and the other for FR, real-time positioning which frequency band and which channel received;
• Power off memory: Replay the very last frequency band and channel
• Independent video and audio signal outputs 



Specifications:

FPV 5.8G 600mW A/V Transmitting/Receiving System TS832 + RC832 - 32CH Edition | RP-SMA

video format supported: NTSC/PAL
Antenna connection: RP-SMA, jack (module side, both TX and RX) 

TX TS832 specs:
Power input: 7.4-16V (3S Lipo suggested)
Transmitting power: 600mA 
Antenna gain: 2db
Working current: 220mA at 12V
Video bandwidth: 8M
Audio bandwidth : 6.5M
Weight: 22g
Dimension: 54x 32x 10mm(excluding antenna)

RX RC832 Specs:

Power input: 12V
Working current: 200mA max
Antenna impedance: 50Ω
Antenna gain: 2db
Video impedance: 75Ω
Video format: NTSC/PAL auto
Dimension: 80x 65 x15mm
Weight: 85g


*Note: TX antenna must be installed properly before it is switched on, power on without install antenna, or a improper antenna was used may easily burn the TX, and such damage is not covered by warranty.






* We found that in recent batch, some of the TX TS-832 come with reversed power supply wires, the first wire from left side is black instead of red, but we also noticed that for the ones with reversed wires, the wires on JST connector side are also reversed, so in this case, if you connect the JST connector to a battery pack with standard polarity JST connector, as both the sides are reversed, so the system can still work properly, but in this case, the black wire is for "Positive" pole, and the red wire is for "negative". In other words, if the first wire from left on the TX module side is black instead of red, then on JST side, the black wire should be connected to the Positive pole of your battery.

The key point is that the first wire/pin from left side as shown on above diagram must be connected to "positive" pole of your power source, so if the wire color mapping is not critical for you, you can leave it without any change for the "wrong" cables, also this TX module with wrong polarity protection, it will not damage the TX even in case the power supply is in wrong polarity. 

For the ones who concern about the color/polarity mapping issue too much, you can follow the below diagram to swap the wires:






Includes/Requires:

Includes:
1 x transmitting unit (TX)
1 x receiver (RX)
2 x antennas (2db)
1 x basic wires set

본제품은 해외구매대행상품이며 입금확인후 배송기간은 2~3일 정도 소요됩니다.
특수경우에 따라 최장 2주일까지 걸릴수도 있습니다.
또한 해외구매대행상품이기에 물건출고후 A/S 및 반품은 불가합니다.

모든 구매대행상품은 해외공장에서 한국소비자께 직배송합니다.
주문시 정확한 수취인 주소기재 바랍니다.
저희 엑스캅터에서 수취인 주소기재오류로 인한 책임은 지지 않습니다.
 


학교 및 연구기관 구매가이드

내맘대로 결제하기

맨위로


WORLD SHIPPING

PLEASE SELECT THE DESTINATION COUNTRY AND LANGUAGE :

GO
close